Faq

Quick answer: Question mark when measuring in autocad?

Instead of the measured distance, AutoCAD suddenly displays only the crosshair cursor with a question mark badge (symbol), no numbers. Please check the commandline prompt for the expected type of the entry. The older command DIST immediately prompted for the points to measure.

Beside above, how do I get rid of the question mark in AutoCAD?

  1. Install the latest updates for AutoCAD (see Install Updates, Add-ons, and Enhancements).
  2. Reset AutoCAD to defaults (See: How to reset AutoCAD to defaults).
  3. Repair or reinstall AutoCAD (See: How to repair or reinstall an AutoCAD installation).
  4. Perform a clean uninstall and reinstall of AutoCAD.

Moreover, how do I turn off Dynmode in AutoCAD?

  1. Press the F12 key to toggle Dynamic Input on and off.
  2. Change the DYNMODE variable to 1 for on, or 0 for off.
  3. Toggle the dynamic input icon in the lower-left or lower-right corner of the program:

In this regard, how do I show measurements in AutoCAD?

  1. Open the Dimension Style Manager using DIMSTY.
  2. Select the dimension style in use.
  3. Select Modify.
  4. Navigate to the Primary Units tab.
  5. Set Unit Format to Decimal.
  6. Set the Precision to be displayed. For whole inches, set the Precision to 0.
  7. In the Suffix box, add the inch symbol (“).
  8. Press OK.

Frequent question, how do I turn on quick measure in AutoCAD? Use Quick Measure when you want to measure something, but don’t want to interrupt your workflow using the interactive measure command. In the Ribbon, in the Home tab, on the Utilities panel, click the Quick ruler icon (measuregeom).The marker is highlighting the fact that the object it was measuring / referencing has been deleted or disassociated. This is particularly using if using constraints or perhaps 3D model geometry. If this is not desired switch the Annotation Monitor off.

INTERESTING:   Autocad express tools menu?

Contents

How do you Reassociate dimensions in Autocad?

  1. Select one or more dimensions to associate or reassociate.
  2. Press Enter and do one of the following: To associate the dimension to specific geometry, enter s (Select object) and select the geometry.
  3. Repeat steps as needed.

How do I disable dynamic UCS?

The crosshairs use the same colors to represent the directions of the axes. 4 On the status bar, click the Dynamic UCS button to turn it off.

How do I enable dynamic UCS in AutoCAD?

With the dynamic UCS turned on, align the XY plane of the UCS with a plane on a 3D solid. To toggle on and off the Dynamic UCS, use the F6 key. Alternatively, type UCSDETECT into the command line and then enter 0 (not-active) or 1 (active).

What is Polar Snap?

PolarSnap restricts cursor movement to specified increments along a polar angle. When you create or modify objects, you can use polar tracking to display temporary alignment paths defined by the polar angles you specify. In 3D views, polar tracking additionally provides an alignment path in the up and down directions.

Why is AutoCAD not showing dimensions?

Go to Ribbon > Dimension pull-down menu > Dimension Style Manager, or use the DIMSTYLE command. Select the style in use and click on Modify… . Go to the Text tab and adjust the Text height accordingly. Confirm with OK and Close.

How do you display measurements?

It needs to be written Length X Width X Height. That is standard for measurements. It makes no difference in the order you have them listed. The end result is the same.

INTERESTING:   Best answer: Block command in autocad shortcut?

How do I use the measure command in AutoCAD?

  1. Click MEASURE.
  2. Choose Area.
  3. Specify points. Use object snaps for precision.
  4. When finished selecting points, press Enter.

How do I get rid of the yellow exclamation mark in AutoCAD?

To toggle the annotation monitor off: At the command line type ANNOMONITOR and set this variable to 0 to turn the alert off.

What is disassociated annotation in AutoCAD?

To quickly locate dimensions or leaders that have lost associativity with their geometry, the yellow ‘badge alerts’ will appear when the Annotation Monitor is turned on. If you hover the cursor over one of the yellow boxes, ‘Disassociated Annotation’ will appear at the cursor’s location.

What is the use of marker in AutoCAD?

You can use either custom markers or AutoCAD points to designate point nodes. If you choose to use AutoCAD points as markers, the marker style can be adjusted with the DDPTYPE command. In this exercise, you will select a new custom marker and superimposed symbol, and then size the marker in absolute units.

Back to top button

Adblock Detected

Please disable your ad blocker to be able to view the page content. For an independent site with free content, it's literally a matter of life and death to have ads. Thank you for your understanding! Thanks